Shop
Showing 1–20 of 24 results
Weldmark 2% Thoriated Tungsten 3/32″ X 7″
Weldmark 2% Thoriated Tungsten 3/32″ X 7″
Tungsten Electrode 3/32” X 7” Ground 2% Thoriated Tungsten
Extremely long lasting and highly durable, these electrodes are a staple in DC welding applications. They are the most commonly used electrodes today and are preferred for their longevity and ease of use. Thorium increases the electron emission qualities of the electrode, which improves arc starts and allows for a higher current-carrying capacity. This electrode operates far below its melting temperature, which results in a considerably lower rate of consumption and eliminates arc wandering for greater stability. Compared with other electrodes, Thoriated electrodes deposit less tungsten into the weld puddle, so they cause less weld contamination.
These electrodes are used mainly for specialty AC welding (such as thin-gauge aluminum and material less than 0.060 inch) and DC welding, either electrode negative or straight polarity, on carbon steel, stainless steel, nickel, and titanium.
During manufacturing, thorium is evenly dispersed throughout the electrode, which helps the tungsten maintain its sharpened edge—the ideal electrode shape for welding thin steel—after grinding. Note: Thorium is radioactive; therefore, you must always follow the manufacturer’s warnings, instructions, and the Safety Data Sheet (SDS) for its use.
Weldmark 2% Thoriated Tungsten 1/16″ X 7″
Weldmark 2% Thoriated Tungsten 1/16″ X 7″
1/16” X 7” Ground 2% Thoriated Tungsten
Extremely long lasting and highly durable, these electrodes are a staple in DC welding applications. They are the most commonly used electrodes today and are preferred for their longevity and ease of use. Thorium increases the electron emission qualities of the electrode, which improves arc starts and allows for a higher current-carrying capacity. This electrode operates far below its melting temperature, which results in a considerably lower rate of consumption and eliminates arc wandering for greater stability. Compared with other electrodes, Thoriated electrodes deposit less tungsten into the weld puddle, so they cause less weld contamination.
These electrodes are used mainly for specialty AC welding (such as thin-gauge aluminum and material less than 0.060 inch) and DC welding, either electrode negative or straight polarity, on carbon steel, stainless steel, nickel, and titanium.
During manufacturing, thorium is evenly dispersed throughout the electrode, which helps the tungsten maintain its sharpened edge—the ideal electrode shape for welding thin steel—after grinding. Note: Thorium is radioactive; therefore, you must always follow the manufacturer’s warnings, instructions, and the Safety Data Sheet (MSDS) for its use.
Tweco Classic No. 2 .030″-.035″ Miller Style 15′ MIG Gun
Tweco Classic No. 2 .030″-.035″ Miller Style 15′ MIG Gun
TWECO Classic 2 Air Cooled 200 Amp MIG Gun
200 AMP 60% Duty cycle MIG with TWECO rear connector suitable for medium duty fabrication.
Features:
- Wide selection of front end consumables available to fit the needs of the application
- Industry standard for 40+ years, oval shaped handle reduces grip required to manipulate MIG gun position
- Balanced to pivot at the center of the handle for ease of use in different welding positions, and thereby reduces operator fatigue
- Gun hanger located at the bottom for ease of resting gun when not in use
- Heavy-duty design for industrial application environments using special plastic composition for high impact crush-resistant handle
- Steel spring strain relief provides support to the Cablehoz® coming out the rear of the handle to minimize wire feed issues
- Mechanical connection of conductor tube and cablehoz within the handle providing excellent current path to the end of the contact tip
- Two (2) ball-point screws are used to secure the Cablehoz® and conductor tube in place
- Trigger contains silver plated contacts with a self cleaning action every time the trigger is engaged & disengaged
- Metal jacket conductor tube
Specifications:
- Amps: 200 A
- Cooling: Air
- Duty Cycle: 60%
- Wire Diameter: .035″
- Connector: Miller Style
- Gas: Carbon Dioxide
CK Worldwide Layzr Tungsten 7″
CK Worldwide Layzr Tungsten 7″
Tungsten Electrode 7” Layzr Non-Radioactive
Best for automated or robotic applications in alternating current (a/c) or direct current (d/c) due to low voltage tolerance (changes in tip to work piece distance) using inverter or transformer based constant current power sources. Good for low-alloyed steels, Non corroding steels, aluminum alloys, magnesium alloys, titanium alloys, nickel alloys, copper alloys. Runs cooler than 2% Thoriated with longer life, low to medium amperage range. Best for low amperage starts.
- AWS A5.12 EWG
- ISO 6848
ATT Head Tube For M-25 Series 100 – 250 Amp MIG Guns
ATT Head Tube For M-25 Series 100 – 250 Amp MIG Guns
Bernard 45° Tube Assembly for Q-Gun Series MIG Guns
Bernard 45° Tube Assembly for Q-Gun Series MIG Guns
CK Worldwide Layzr Tungsten 1/8″ X 7″
CK Worldwide Layzr Tungsten 1/8″ X 7″
Tungsten Electrode 1/8” x 7” Layzr Non-Radioactive.
Best for automated or robotic applications in alternating current (a/c) or direct current (d/c) due to low voltage tolerance (changes in tip to work piece distance) using inverter or transformer based constant current power sources. Good for low-alloyed steels, Non corroding steels, aluminum alloys, magnesium alloys, titanium alloys, nickel alloys, copper alloys. Runs cooler than 2% Thoriated with longer life, low to medium amperage range. Best for low amperage starts.
- AWS A5.12 EWG
- ISO 6848
Weldmark 2% Thoriated Tungsten 1/8″ X 7″
Weldmark 2% Thoriated Tungsten 1/8″ X 7″
1/8” X 7” Ground 2% Thoriated Tungsten Electrode
Extremely long lasting and highly durable, these electrodes are a staple in DC welding applications. They are the most commonly used electrodes today and are preferred for their longevity and ease of use. Thorium increases the electron emission qualities of the electrode, which improves arc starts and allows for a higher current-carrying capacity. This electrode operates far below its melting temperature, which results in a considerably lower rate of consumption and eliminates arc wandering for greater stability. Compared with other electrodes, Thoriated electrodes deposit less tungsten into the weld puddle, so they cause less weld contamination.
These electrodes are used mainly for specialty AC welding (such as thin-gauge aluminum and material less than 0.060 inch) and DC welding, either electrode negative or straight polarity, on carbon steel, stainless steel, nickel, and titanium.
During manufacturing, thorium is evenly dispersed throughout the electrode, which helps the tungsten maintain its sharpened edge—the ideal electrode shape for welding thin steel—after grinding. Note: Thorium is radioactive; therefore, you must always follow the manufacturer’s warnings, instructions, and the Safety Data Sheet (SDS) for its use.
CK Worldwide 2% Ceriated Tungsten
CK Worldwide 2% Ceriated Tungsten
7” 2% Ceriated Tungsten
These electrodes perform best in DC welding at low current settings but can be used proficiently in AC processes. With its excellent arc starts at low amperages, Ceriated tungsten has become popular in such applications as orbital tube and pipe fabricating, thin sheet metal work, and jobs involving small and delicate parts. Like thorium, it is best used to weld carbon steel, stainless steel, nickel alloys, and titanium, and in some cases it can replace 2 percent Thoriated electrodes. Ceriated tungsten has slightly different electrical characteristics than thorium, but most welders can’t tell the difference.
Using Ceriated electrodes at higher amperages is not recommended because higher amperages cause the oxides to migrate quickly to the heat at the tip, removing the oxide content and nullifying its process benefits.
CK Worldwide Lanthanated Tungsten 3/32″ X 7″
CK Worldwide Lanthanated Tungsten 3/32″ X 7″
3/32” X 7” 2% Lanthanated tungsten electrodes (AWS classification EWLa-2) contain a minimum of 97.80 percent tungsten and 1.30 percent to 1.70 percent lanthanum, or Lanthana, and are known as 1.5 percent Lanthanated. These electrodes have excellent arc starting, a low Burn off rate, good arc stability, and excellent re ignition characteristics—many of the same advantages as Ceriated electrodes. Lanthanated electrodes also share the conductivity characteristics of 2 percent Thoriated tungsten. In some cases, 1.5 percent Lanthanated can replace 2 percent Thoriated without having to make significant welding program changes.
Lanthanated tungsten electrodes are ideal if you want to optimize your welding capabilities. They work well on AC or DC electrode negative with a pointed end, or they can be balled for use with AC sine wave power sources. Lanthanated tungsten maintains a sharpened point well, which is an advantage for welding steel and stainless steel on DC or AC from square wave power sources.
Unlike Thoriated tungsten, these electrodes are suitable for AC welding and, like Ceriated electrodes, allow the arc to be started and maintained at lower voltages. Compared with pure tungsten, the addition of 1.5 percent Lanthana increases the maximum current-carrying capacity by approximately 50 percent for a given electrode size.
CK Worldwide 1.5% Lanthanated Tungsten 1/8″ X 7″
CK Worldwide 1.5% Lanthanated Tungsten 1/8″ X 7″
3/32” X 7” Lanthanated tungsten electrodes (AWS classification EWLa-1.5) contain a minimum of 97.80 percent tungsten and 1.30 percent to 1.70 percent lanthanum, or Lanthana, and are known as 1.5 percent Lanthanated.
These electrodes have excellent arc starting, a low burn off rate, good arc stability, and excellent re ignition characteristics—many of the same advantages as Ceriated electrodes. Lanthanated electrodes also share the conductivity characteristics of 2 percent Thoriated tungsten. In some cases, 1.5 percent Lanthanated can replace 2 percent Thoriated without having to make significant welding program changes.
Lanthanated tungsten electrodes are ideal if you want to optimize your welding capabilities. They work well on AC or DC electrode negative with a pointed end, or they can be balled for use with AC sine wave power sources. Lanthanated tungsten maintains a sharpened point well, which is an advantage for welding steel and stainless steel on DC or AC from square wave power sources.
Unlike Thoriated tungsten, these electrodes are suitable for AC welding and, like Ceriated electrodes, allow the arc to be started and maintained at lower voltages. Compared with pure tungsten, the addition of 1.5 percent Lanthana increases the maximum current-carrying capacity by approximately 50 percent for a given electrode size.
- AWS A5.12 EWLa-1.5
- ISO 6848 WL15
Miller M-100 10′ MIG Gun
Miller M-100 10′ MIG Gun
Miller MIGmatic M-100 100Amp Air-Cooled MIG Welding Gun
Processes
· MIG
· Flux Cored
Features
· 3 piece nozzle construction extends nozzle life by reducing wear and helps prevent rocking of nozzle on contact tip adapter
· Interchangeable contact tips
· Brass contact tip adaptor helps prevent galling, sticking & stripping of threads
· Single piece high-impact handle is almost indestructible with ergonomic design
· Steel spring strain relief protects power cable from wear and helps prevent liner from kinking, allowing better wire feed ability.
· 360° rotatable gooseneck
· Interchangeable monocoil liners
Specifications
· Cable Length: 10′
· Rated Output: 100A
· Duty Cycle: 100% with CO2 gas, 60% with mixed gas
· Standard Wire Size: .030″
Tweco Classic No. 3 .035″-.045″ Miller Style 15′ MIG Gun
Tweco Classic No. 3 .035″-.045″ Miller Style 15′ MIG Gun
Tweco Classic 3 Air Cooled MIG Gun 300 Amp
300 AMP 60 Duty cycle MIG gun with Miller rear connectors. Suitable for medium/heavy duty fabrication.
Features:
- Wide selection of front end consumables available to fit the needs of the application
- Industry standard for 40+ years, oval shaped handle reduces grip required to manipulate MIG gun position
- Balanced to pivot at the center of the handle for ease of use in different welding positions, and thereby reduces operator fatigue
- Gun hanger located at the bottom for ease of resting gun when not in use
- Heavy-duty design for industrial application environments using special plastic composition for high impact crush-resistant handle
- Steel spring strain relief provides support to the Cablehoz® coming out the rear of the handle to minimize wire feed issues
- Mechanical connection of conductor tube and cablehoz within the handle providing excellent current path to the end of the contact tip
- Two (2) ball-point screws are used to secure the Cablehoz® and conductor tube in place
- Trigger contains silver plated contacts with a self cleaning action every time the trigger is engaged & disengaged
- Metal jacket conductor tube
- Enhanced direct plug capabilities
Specifications:
- Amps: 300 A
- Cooling: Air
- Duty Cycle: 60%
- Wire Diameter: .045″
- Connector: Miller Style
- Gas: Carbon Dioxide
Weldmark TIG Collet 1/16″ For HW-20, 9, 25 Torches
Weldmark TIG Collet 1/16″ For HW-20, 9, 25 Torches
Tweco Flux Core SEFC 350A Lincoln Style 15′ MIG Gun
Tweco Flux Core SEFC 350A Lincoln Style 15′ MIG Gun
TWECO Fluxcored SEFC MIG Gun
350 AMP 60% Duty cycle MIG gun with Lincoln Style rear connectors. Suitable for medium/heavy duty fabrication
Features:
- For use with all gasless wires
- High Impact-Resistant One-Piece “Straight” Handle
- Metal “Paddle” style trigger lever
- Micro-Switch Trigger Design incorporates a button style switch for start/stop wire feed
- Spare Trigger Leads in Cablehoz
- Heavy Duty design and front-end consumables
- Rugged & Duraable power Cablehoz with proven abrasion & heat ressitance
Specifications:
- Amps: 350 A
- Cooling: Air
- Duty Cycle: 60%
- Wire Diameter: 3/32″
- Connector: Lincoln Style fits LN 7, 8, 9 , SP200
- Gas: Carbon Dioxide
Lincoln Magnum 100L Gun 10′ .025-.045 Liner
Lincoln Magnum 100L Gun 10′ .025-.045 Liner
Semiautomatic Gas-Shielded Guns
Magnum® guns for MIG or flux-cored welding feature our classic curved handle and are available in a number of amperage ranges for use in many applications.
Top Features
· Extremely small, lightweight gun that’s great for most home, farm and small shop projects, auto body work and light maintenance or repair applications. Includes gun connector.
· One-piece modular trigger assembly – Molded out of high heat resistant material to withstand head and spatter and ensure long life.
· Gun tube design – Armored with an electrically insulated metal jacket optimizing fine wire welding performance.
· Abrasion-resistant, extruded rubber jacket – Adds strength and long life to the cable.
· Classic curved handle – Lightweight and balanced, providing a comfortable grip to reduce fatigue.
Processes
Flux-Core Gas Shielded
Wire Diameter Range
.025-.045 in. (0.6-1.2 mm)
What’s Included
· Contact Tip
· Gas Diffuser
· Gas Nozzle
· Insulator
· Cable Liner
· Gun Tube (60°)